液冷头盔致冷效能的医学研究

在45℃高温条件下,应用液冷头盔给10名被试者的头颈部致冷,散热效能较高,可带走安静时30.9％～48.3％的代谢产热。降低身体的热蓄积,减少出汗,减慢心率、直肠温度和皮肤温度的上升速率。对头颈部致冷可降低身体的热紧张度50％～70％,明显改善对温热的舒适感觉。同时表明,致冷液温、流量及液流走向,对致冷效能均有显著影响。为液冷头盔及致冷装置的设计,提供了医学实验依据。     

逆升压电子设备冷却系统控制方案的研究

分析了目前国内一些飞机基于三点温度控制方案的逆升压电子设备冷却系统的缺陷 ,提出了一种新的系统控制方案 ,即基于飞行速度和高度的逆升压电子设备冷却系统的控制方案。这一方案不需要人工干预 ,可实现全自动化。     

Radiative and hybrid cooling of infrared space telescopes

The designs of cold space telescopes, cryogenic and radiatively cooled, are similar in most elements and both benefit from orbits distant from the Earth. In particular such orbits allow the anti-sunward side of radiatively-cooled spacecraft to be used to provide large cooling radiators for the individual radiation shields. Designs incorporating these features have predictedT _tel near 20 K. The attainability of such temperatures is supported by limited practical experience (IRAS, COBE). Supplementary cooling systems (cryogens, mechanical coolers) can be advantageously combined with radiative cooling in hybrid designs to provide robustness against deterioration and yet lower temperatures for detectors, instruments, and even the whole telescope. The possibility of such major additional gains is illustrated by the Very Cold Telescope option under study forEdison, which should offerT _tel5 K for a little extra mechanical cooling capacity.     

带肋壁与出流孔内流通道的流阻特性

采用根据相似理论几何放大的模型，在流动相似的条件下，实验研究了带肋壁与出流孔内流通道的流阻特性。在内流通道进口雷诺数为40000-80000，通道总出流比为0．30—0．60的范围内测量了通道压力损失系数Cp的分布，分析了通道进口雷诺数和通道总出流比对Cp的影响规律。结果显示：在通道进口雷诺数一定时，随总出流比的提高，通道内Cp减小，压力损失减小；在通道总出流比一定时，通道进口雷诺数对Cp无显著影响。另外，在比较了当前内流通道流阻工程算法与实验结果的基础上，提出了对当前流阻算法的改进措施。     

大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。     

An improved approach for rainfall estimation over Indian summer monsoon region using Kalpana-1 data

In this paper, an improved Kalpana-1 infrared (IR) based rainfall estimation algorithm, specific to Indian summer monsoon region is presented. This algorithm comprises of two parts: (i) development of Kalpana-1 IR based rainfall estimation algorithm with improvement for orographic warm rain underestimation generally suffered by IR based rainfall estimation methods and (ii) cooling index to take care of the growth and decay of clouds and thereby improving the precipitation estimation.     

热力学排气系统中节流效应及其冷量利用分析

为更好地理解热力学排气系统(TVS)的运行机理，优化其运行参数，针对节流装置，建立了热力学模型，讨论了节流过程中状态参数的变化规律，对比了单相气体、单相液体节流的性能特性，进一步揭示了焦汤节流效应的原理，分析了不同节流背压下节流前低温工质(液氢和液氧)压力和温度对节流性能的影响，并结合TVS实际应用，阐述了节流最大制冷量的利用效果，提出了优化的TVS工作区间。研究表明：在节流过程不发生相变情况下单相气体节流制冷效应要比单相液体节流制冷效应更加显著；而在节流过程发生相变情况下液体节流至两相后，由于空化吸热导致流体温度降低，对于液氢，0.5MPa的压降可产生接近3 K的温降。对于液体节流，节流前压力对节流过程影响可忽略，〖JP2〗而节流前温度和节流背压对节流过程起主导作用；对于液氢在在轨运行工况下，考虑到节流制冷量的充分利用，同时保证换热过程体积含气率不高于90%，推荐TVS系统中节流背压范围为75～143 kPa。     

深冷组合循环发动机吸气模态循环分析与设计可行域研究

为了研究类似SABRE3结构的深冷组合循环发动机,建立了基于部件法的发动机设计点热力学计算模型,提出了发动机氦循环新的循环效率和循环特征参数的定义。考虑发动机参数的物理限制条件及不同工质循环之间的相互影响,求解得到了空气路、氦气路重要参数的设计可行域。在可行域内开展了空气路和氦气路的循环分析,获到了冷却当量比、性能参数等主要参数的分布结果。结果表明:此发动机空气热功转换比ηt2为0.02～0.746。氦循环设计可行域受ηt2及换热器热负荷限制;循环起始温度和热负荷限制确定的情况下,ηt2越低氦循环可行域越窄。降低发动机冷却当量比的关键是:提高换热器1的氦出口温度以降低氦流量;当换热器1和换热器2的氦出口温度同时取得最大值时,冷却当量比取得最小值。换热器1和2的氦出口温度分别取1200K和1300K时,空气路可行域内冷却当量比为0.917～2.64。     

基于试验设计-遗传算法的船用柴油机冷却系统多目标优化

为了获取某型船用柴油机冷却系统的最佳运行参数,在柴油机可靠运行的前提下,尽量提升动力性和经济性。建立了柴油机工作过程-燃烧室-冷却系统耦合仿真模型,提出试验设计-遗传算法优化算法,该算法具备节省试验成本和多目标全局寻优的优势,选取柴油机的6个典型推进工况点进行研究,采用该算法对冷却系统运行参数开展多目标优化设计,优化设计以海、淡水泵转速为变量因子,以提升动力性参数和经济性参数为目标,以涡前排温、淡水出机温度和峰值缸压为约束条件,优化后,在低负荷点,淡、海水泵节省功耗79.4%、71.73%,扭矩提升7.2%,有效功率提升7.6%,热效率提升8%,耗油率降低6.73%,摩擦功降低9.71%,峰值缸压降低5%。研究结果表明：耦合仿真模型与实机更加贴近;试验设计-遗传算法在解决强耦合、非线性系统的多目标优化问题具备成本低、效率高、精度高的优点。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.